VAGTACHO versão 5.0 (odometro, pin code, chaves, eprom)

VAGTACHO version 5.0

Suporta VDO com 24C32 ou 24C64

o vagtacho usb versão 5.0 inclui as funç~oes do usb 4.52 ， vagtacho usb 4.0，e vagtacho usb 3.5

Quadrantes VAG / Programador eprom Immo box !

Windows 7 32bit ,Vista, Win XP, Win 98 !

.Funções principais:

1.Ler a info da ECU

2.Ler o pin

3. ajuste de KM

4.Leer eeprom

5.programar nova chave

6.Escreveer  eeprom

7.Apagar erros da centralina

8.ver o buffer da memoria

Suporta alguns quadrantes VDO da VW do ano 2009-2011 com MCUNEC e memoria 24C32 or 24C64 .

Programador de tranponders Megamos ID48! Pre-programação dos  TP2x com componente de segurança lido da immo box!

Novo programador de chaves VAG co mquadrante VDO e CAN bus! (protocolo TP2 e UDS)

Nota: Precisa de tranponders TP22,23,24,25 !

Lista de carros suportados:

Volkswagen

Golf 6, Jetta, Polo, EOS with VDO dash 2009 - 2011, nota: nem todos  os quadrantes sao suportados!

Golf 5, Caddy, Touran, Jetta, EOS com quadrante VDO 2003 - Junho.2006

Golf 4, Bora com VDO ou Motometer/Bosch  1997-2003

Beetle com quadrante Marelli 1998 - 2005

Passat, Jetta,com quadrante VDO, Marelli ou Motometer  : 1997-2004

Polo com quadrante VDO ou Motometer  1999-2006 (1999-2002 so mudança de km)

Sharan com quadrante VDO : 2000-2004(so muda km)

Caddy, Lupo com quadrante VDO ou Motometer 1997 - 2002(KM So)

Transporter com quadrante VDO dash 1998 - 2000

LT35 ( Temic immo box) 1999-2003 (pin code apenas)

Gol ( Kostal immo box) 1999-2003 (pin code apenas)

Seat

Altea, Leon, Toledo com quadrante VDO 2003 - 6/2006

Leon, Toledo, Cordoba, Ibiza com quadrante VDO ou Motometer 1997-2003

Alhambra com quadrante VDO 2000 - 2004(Km apenasmileage change only)

Inca com quadranteVDO or Motometer 1997 -2000(mileage change only)

Skoda

Octavia II with VDO dash 2005 - 6/2006

Octavia, Fabia with VDO dash 1997 - 2004

Audi

A3 VDO dash 2003 - 2005

A3,A4,A6 VDO dash 1997 - 2000

A3,TT,A6 Magnetti Marelli dash 1998 - 2003

A4 Bosch dash 2000 - 2008 - Read/write of encrypted data with V4.5!

A4,A6,A8 1995-1999 (immo box - read pin code)

2.vag tacho usb version 4.52

V

Your Vagtacho interface will works with software vesrion 5.0 for the new VDO dashes with UDS protocol from year 2009+

Programming of new keys to VAG cars which are into FAZIT database.

Works with cars which has got locked key programming channel, or pin code is not accepted.

No need to wait up to 30 minutes for the key programming procedure.

With this upgrade, Vagtacho can program the new key in one minute

.

3.Vagtacho version 4.0

 VAG Kombiinstrument / Immo box eeprom programmer!

Windows 7,Vista, Win XP, Win 98 compatible software!

Works on any computer which has got USB port!

Most of VAG dashes from 1997 to 2006 are supported!

Direct programming of Megamos ID48 (JMA-TP08) chips

to VAG cars on CAN bus from November.2003 to June.2006

Transponder Maker Pro is required for pre-programming of these chips.

Note: TP22,23,24,25 transponders are NOT required!

2.List of supported VAG cars:

Volkswagen

Golf 5, Caddy, Touran, Jetta, EOS with VDO dash 2003 - June.2006

Golf 4, Bora with VDO or Motometer/Bosch dash: 1997-2003

Beetle with Marelli dash: 1998 - 2005

Passat, Jetta, with VDO, Marelli or Motometer dash: 1997-2004

Polo with VDO or Motometer dash: 1999-2006 (1999-2002 mileage change only)

Sharan with VDO dash: 2000-2004(mileage change only)

Caddy, Lupo with VDO or Motometer dash 1997 - 2002(mileage change only)

Transporter with VDO dash 1998 - 2000

LT35 ( Temic immo box) 1999-2003 (pin code read only)

Gol ( Kostal immo box) 1999-2003 (pin code read only)

Seat

Altea, Leon, Toledo with VDO 2003 - 6/2006

Leon, Toledo, Cordoba, Ibiza with VDO or Motometer dash 1997-2003

Alhambrawith VDO 2000 - 2004(mileage change only)

Inca with VDO or Motometer 1997 -2000(mileage change only)

Skoda

Octavia II with VDO dash 2005 - 6/2006

Octavia, Fabia with VDO dash 1997 - 2004

Audi

A3 VDO dash 2003 - 2005

A3,A4,A6 VDO dash 1997 - 2000

A3,TT,A6 Magnetti Marelli dash 1998 - 2003

A4 Bosch dash 2000 - 2005

A4,A6,A8 1995-1999 (immo box - read pin code)

3.how to programmer keys with vagtacho usb4.0

Switch ON ignition with any key new or old, no mater which one. Start software, select "VDO NEW - CAN bus" from menu. Press "Connect Selected ECU" button, after 5 seconds the data of the dash will be shown on screen. Press "Program New Key", software will read data from the dash and after few seconds a new window will be open. See the picture. ID numbers of the transponders which are stored into memory will be shown

Press "Save Data to File" and save immobiliser's data somewhere in you computer. After you had saved file, press "Close" - "Disconnect", switch iginiton off and remove key. Start TMPro and upload that file in software. TMPro will check file and will open a menu where you can program new transponder key for this car. Insert the new key in TMPro box and program it.

This is TMPro module#146 window. Insert transponder key with new Megamos ID48 chip and program it.

Press "Add Key" and a message will be shown. Switch ON ignition with key which you want to program! The key may be new - already programmed with TM Pro, or old - key which has been used with the same car! Vagtacho will check the key. If this key is already programmed to the car, or it is from another car, Vagtacho will show warning message on screen and won't program this key!

If everything is ok, Vagtacho will add the new key into the data of immobiliser and will show ID number of new key on screen. See the red mark on the picture. Now you are ready to program the new transponder key into the immobiliser. Press "Write Keys" to complete programming procedure !

Press "Write Keys" and the warning window will be open. If you are sure that everything is all right, press"Continue", otherwise press "Cancel". If you press "Cancel" nothing will happens, and the data won't be written into immobiliser. After pressing "Continue" Vagtacho will writes the data into immobiliser after few seconds. The dash will be reset, and the programming procedure will be completed!

This is the last step, after this the new data will be written into immobiliser! If you have marked and erased some keys, they will NOT works anymore!

This picture shows the final Vagtacho window. If you have switched ON ignition with key which is already programmed by TMPro, the warning lamp of immobiliser on the dash will be turned off. The new key is already stored into immobiliser and you can start engine!

If the immobiliser's warning lamp on the dash is still flashing, there is some error in programming procedure, you can check the transponder key - see how to do this on the next picture!

Switch ON ignition with the key which you want to test! Start software, select "VDO NEW - CAN bus" from menu, and press"Transponder Check". Vagtacho will connects immobiliser. Press "Read ECU Info" button, and wait about 10 seconds. The information about this transponder key will be displayed on screen, see the next picture. You can press "Read ECU Info" to testing of transponder key again. This procedure is optional, and is not required when programming the new keys.

Transponder variable part and transponder locked must be "YES", otherwise there are errors in programming of the new key with TMPro!

Transponder fixed part must be "YES" otherwise the key is still not programmed into immobiliser, or Vagtacho programming procedure is not completed successfully. In case of such error, repeat whole programming procedure again with another new transponder! All parameters must be set "YES"!